Review – Tech Gear Pencil Case

Finding the right case is a difficult thing, there’re so many options that come in all different sizes, and with features ranging from tons of little pockets and organizational tools to nothing at all. Even where a zipper is positioned can really affect how convenient a product is to use on a day-to-day basis. So today I’ll be looking at an inexpensive pencil case available in a wide range of areas (at least it was when I bought it at a grocery store, but it takes time to properly test a case and I don’t know what’s going on with them now).

The Tech Gear pencil case is a simple thing, being made of mostly black nylon in a rectangular-ish shape that’s about 8” long and 4½” wide. There are two support pieces, one going around the bottom, and another on the “lid” and they keep everything roughly in the right place. Just underneath this support piece is the zipper, which runs along the top edge. When unzipped, the “lid” (which has a rubber logo patch, 5-stripe “design”, and possibly a different color upper half) hinges back along one of the long edges revealing the inside, which is just a “bucket” about 1” deep where you can dump things. This “hinge” is reinforced by another piece of nylon both inside and out.

The inside is a smoother texture than the outside, with several of the seams covered up by a plastic-ish, almost electrical-tape feeling material. There’s a tag that tells you it was made in China, but otherwise it’s just an empty cavern into which you can dump whatever you want that’ll fit. And that is pretty much anything that is the same length or shorter than a standard, unsharpened pencil (about 7½”, you might be able to squeeze longer things in if you’re creative) and about 1¼” thick (even that might be stretching it). And that’s a fair amount of stuff. I’ve been using it to carry around my “to-review” items and never had a problem with space. I’ve only got around 15 items in it now, but it can hold 30 writing implements and a few other bits and bobs comfortably.

But it is a cheap case, so how well does it hold up? Reasonably, I’ll say. It’s been a long time since I went to school (and I just used a Ziploc for my pencil case then) and I know I would’ve been much harder on a case then than I am now, but after carrying it around for a while now there is very minimal wear (a loose thread here and there and the rubber patch on the front is a little scuffed, but nothing significant). Still, I can see a lot of the cheapness in its build quality; most seams are unfinished and liable to tear or unfurl, and the material itself isn’t that strong a stuff in the first place. The zipper works but the material is cheap and soft (and paint already flecking), etc. For someone like me who won’t put it through much hard work it’s fine and’ll probably last for quite a while, but in school I’d say it’s about a 1-year bag.

And that’s pretty much it. The bag has some organizational problems but it’s also fairly small so nothing should get too buried. And it’s got some craftsmanship problems but for the price you couldn’t really expect better. It’s good for what it is and if that’s what you need it’s easy enough to get. So if you just need something to dump your pencils in and won’t worry about having to replace it later because it’s cheap, this one’s a good thing to look at.

Review – Simple Pencil Extender

Pencil extenders are something I haven’t looked into very much. I am able to “comfortably” use a pencil well into a stub, and would just as soon have that stub as a backup and get a new pencil when it gets smaller (and now I’ve mostly swapped to mechanical pencils). But that does mean I have quite a few stubs lying around, and maybe with some inexpensive “Chinese” (don’t know for sure, but it seems likely) pencil extenders I can breathe new life into them.

This one is a bit of an anomaly to me as I didn’t get it myself (it was a gift), it has no identifying markings, and I can’t seem to find it specifically online anywhere. I have found an eBay listing that highly resembles it, but I don’t quite know about it. Still, it is strikingly close to other, more hexagonally shaped versions that can be found all over the place and likely use the same collet.

The device is immensely simple: a rounded wooden dowel is crimped to a tube of metal with a slit near one end and a separate metal band wrapped around it. When a pencil is inserted into the metal tube the band can be slid down to tighten and secure the pencil stub in place. It’s basically a collet that slides instead of screws, and while it works there are some problems. For example, the pencil stubs that can be used must be of a very specific size. Standard hexagonal pencils fit (think Paper:Mate Americans) but the larger art pencils and every round pencil I’ve found (including all colored pencils) have been too big. In general it seems a coat of paint is all the difference it takes between fitting and not.

And even when a pencil does fit it isn’t held very securely. Sliding the metal collar does clamp the collet tube down a bit but a good tug and the pencil comes free, though it is held in well enough that typical shakes don’t knock it loose. And the metal tube itself isn’t very well fitted to the wooden body and the two can easily be persuaded to part ways.

Still, with the cost seemingly being almost nothing, it does a tolerable job. The pencil is held securely enough to write with, and can be used comfortably as long as there is still pencil to grip (the collet is not a nice bit to hold on to). It is fairly lightweight, which is good for portability but bad if you really want your pencil to feel the same as it did when it was longer. And even though the construction is shoddy they cost about as little as a pencil or two so if they help you finish a couple they’ll’ve been worth it.

Review – Master Mechanic Carton Cutter

With so many options, one carton cutter review just wasn’t enough, and I am now back to review one that has a higher price. But does that make it better quality?

photo-127

The short answer is yes: it is better quality, but I’ll just go over a few things. The cutter has a bent and nicely shaped/joined sleeve made out of an unknown metal (probably steel), with an insert that is a folded piece of metal that will hold a razor blade. It also has a cutout “spring” that creates the tension instead of the body doing that, making it more pleasant to use. The sleeve also has a nice, easy-to-hold white paint applied, which makes it easier to see. The Master Mechanic logo that is printed on top of this looks nice but wears off easily and looks unsightly when it does.

photo-128

Use is easy and smooth, tapping (a hard surface) both to deploy and retract the blade-holding mechanism (placing the back on a hard surface and pushing firmly will deploy the blade, and doing the reverse with the blunt part of the front will retract it), but it does have a way it “likes” to go in and works better that way. The razor blades that are included are also slightly better than the cheaper knife, but in general one won’t get much use out of single-edge razor blades, which are sharp but cheap and prone to snapping or deforming.

photo-129

Is it worth it to buy a better version of such simple product? Probably not for most people. While this is a better carton cutter than cheaper ones, it isn’t really less dangerous or easier to use per-se. The fit and finish are as good as one could reasonably expect on a product this cheap; the amount of friction on deployment is constant; and the device will likely last for a long time. Still, a carton cutter isn’t a tool most people will be worrying about, and the less expensive ones would be easier to replace if they were misplaced or damaged.